DUB-100 Error code

Info

The screen is displayed with a pastel blue background and indicates the current operating step or procedural status to the user.

Low Priority Alarm

The screen is displayed with a solid yellow background, and a two-tone audible alarm is generated when a low priority alarm occurs.

Medium Priority Alarm

The screen is displayed with a solid yellow background accompanied by flashing windows, and a three-tone audible alarm is generated when a medium priority alarm occurs.

High Priority Alarm

This device does not include high priority alarm conditions.

---

The following are general alarms.

Err Code	Description	Corrective Active
E 01	Board Communication Err	No response or abnormal communication from board. Reboot the device. If the error repeats, contact the distributor.
E 02	Board Operation Err	EEPROM data or version abnormality detected. Reboot the device. If the error repeats, contact the distributor.
E 03	FAN Err	Check FAN operation. Continuous use may increase temperature and stop output. If the error repeats, contact the distributor.
E 04	Internal Temperature Err	Internal temperature is too high, and output has been stopped. Check installation location and ventilation. Output remains stopped until the internal temperature returns to normal range.
E 05	Panel Button Err	Panel button abnormality detected. Reboot the device. If the error repeats, contact the distributor.
E 06	Medisonic Button Input Err	Abnormal switch input has been detected. Press the confirm button and inspect the switch.
E 07	Medipolar Button Input Err
E 08	Bipolar Input Err
E 11	Medisonic Foot Switch Input Err
E 12	Medipolar Foot Switch Input Err
E 13	Bipolar Foot Switch Input Err
E 16	Button Err	Simultaneous input from two switches detected. Output remains stopped until all switches are released.
E 17	SD card Err	Check SD card status. The format may be incorrect or the SD card may be defective. If the error repeats, contact the distributor.
E 41	Output Err	Abnormal output signal has been detected. Equipment inspection is required. If the error repeats, contact the distributor.
E 49	Patient Circuit Err	Patient leakage current above the reference limit detected during operation. Check patient condition and device connection status before use.

The following are MEDISONIC alarms.

Err Code	Description	Corrective Active
E 21	Reuse Err	Risk of contamination and performance degradation due to reuse.
E 22		More than 24 hours have elapsed after insertion and Test. Risk of contamination due to prolonged exposure.
E 23	Usage Limit Err	Repeated reuse may prevent normal output operation. Device usage is restricted.
E 24	ED Communication Err	Check connector connection status and foreign material, then reconnect.
E 25		Repeated communication errors may damage the connection area. Check and reconnect.
E 26	ED Data Err	ED status abnormality detected. Replace the device.
E 27	Test Err	ED is outside the normal range after three or more Tests. If repeated, contact the distributor.
E 28	Output Failure Err	Blade pressure abnormality or ED abnormality detected. Clamp approximately two-third of the jaw, or select another surgical site.
E 29	Metal Err	Output abnormality caused by hard material. Select another surgical site.
E 30	Output Circuit Err	Single fault condition detected. Equipment inspection is required due to output signal abnormality. If repeated, contact the distributor.

The following are MEDIPOLAR alarms.

Err Code	Description	Corrective Active
E 42	Short Err	Metal or excessive liquid environment detected. Change the surgical site and restart operation. If the error repeats, contact the distributor.
E 43	Jaw Open Err	Jaw is not completely closed or tissue thickness is excessive. If the Jaw is open, close it completely and restart operation. If the Jaw is already closed, change the tissue and restart operation. If the error repeats, contact the distributor.
E 47	Sealing Interrupted Err	Output was interrupted before sealing was completed. Check the surgical site.
E 48	Sealing Failure Err	Sealing was not completed within the set time. Retry sealing or select another surgical site.